If you’re interested in music production, the sky’s the limit. During this one day event we would record a four piece band then mix the track. You can also use the line-in audio jack to record an instrument in macOS. I was deeply honoured to be invited to Studiya Igorya Matvienko recording studios in the Russian capital, Moscow to lead an audio engineering workshop in association with Soyuz microphones and APS monitors. You might want to use it to record using two different microphones in GarageBand, for instance. There’s no guarantee that the headphone jack will remain a built-in feature in future Macs, but while it’s still there, you can use it to connect external audio input devices without needing an expensive adapter. This is a quick overview on bypassing the built-in microphones of the Zoom H4n so that you can track 4 external channels simultaneously using the 3.5mm TRS jack underneath the built-in microphone module. Using External Devices on Modern macOS Devices Using 4 inputs on the H4n (by-passing the internal mics) My first video post on. Certain audio input devices may also come with their own control software, allowing you to further calibrate your input settings. You may also have additional controls and settings available to you, depending on the type of device you’re using. And of course if you have any questions about any of this stuff, I encourage you to leave it in a Comment below.You’ll be able to see the current volume value (listed in decibels), as well as the input volume (a decimal figure, up to a maximum of 1) next to the Master volume slide for your device. If you liked the sound that I got in the video when using the XLR inputs on my Zoom H4n, the mics that I used were a wired Tram TR50, and an Audio Technica 4053b. I figured the HV20 crowd might be into using Sescom cables too, so I may as well go ahead and try it out.
#Using h4n mac audio input pro
Functioning as a 2-input/2-output USB audio interface for PC or Mac, the H4n Pro enables you to record directly to your computer. The improved noise floor (-120 dBu EIN) captures audio at lower volumes with less noise and fewer artifacts. Instead I used my Panasonic PV-GS200 mini DV camera. The H4n Pro features high performance, low-noise mic preamps with recording resolutions up to 24-bit/96 kHz. I’m still saving up to buy a DSLR of my own (the DSLR’s I’ve used in my other videos were all borrowed), so I didn’t have one to use on this test. These cables were designed with DLSR cameras in mind, but they work with other kinds of video cameras. If you’re using a Panasonic GH1 or GH2, then you want the special cable that Sescom makes with a 2.5mm male plug for the camera’s sub-mini mic input: If you want to go ahead an outfit yourself with this cable, this is the one I used: I really think if you’re considering buying a Sescom cable, getting one that has the headphone output is a must. Being able to listen to your audio is a very important thing.
However, I would have gotten an even better sound if I had the option to turn off the AGC (automatic gain control) in the camera I was using. These Sescom DSLR cables are perfect examples of high-quality, purpose built problem solving cables.Īll in all, I found that I got a very good sound using this cable. If you’re going to split a signal, you’re much better off using a cable or a device that was custom designed for the task at hand, rather than Frankensteining together cheap Radio Shack adapter cables. People often worry that if they split an audio signal, it will degrade the quality of the sound. This is a legitimate thing to worry about.
#Using h4n mac audio input portable
This enables you to feed the sound from your portable digital recorder directly into your camera’s mic input, while listening on headphones at the same time. Instead of it just being a straight cable with a -25dB pad, it’s a Y-Cable with a female 3.5mm headphone jack. That’s why they make special Sescom cables with a headphone tap.
Additionally, there is a mic/line input via the stereo 1/8' input jack. The H4n Pro offers two locking XLR/TRS combo jacks, each with switchable phantom power. Using the H4n as an audio interface The H4ns USB port allows it to send and receive digital data and to act as a 2-input / 2-output interface, operating at sampling frequencies of either 44.1 or 48kHz. The problem with using a regular Sescom cable is that it consumes the headphone output on your portable digital recorder, leaving you with no way to listen to the sound. Functioning as a 2-input/2-output USB audio interface for PC or Mac, the H4n Pro enables you to record directly to your computer. As usual, I figured I’d share my findings with you. A company called Markertek was kind enough to send me one of these cables to test out. Well, it turns out that Sescom makes another variation of this cable which makes it possible to also monitor your audio on headphones as you record. There’s been a lot of interest in a recent post I made on Sescom cables, and how they help you get good audio inside a camera when working with a portable digital recorder.